Bộ điều khiển Yaskawa Sgma 3 Series 3 Phase Servo Motor Driver Mechatrolink SGDS-08A12AY562
Industrial Servo MotorYASKAWA SGDS-08A12AY562 SERVO DRIVER 750W Mechatrolink
Quick Details
Brand Name:Yaskawa
Model Number:SGDS-08A12AY562
Input Voltage: 200-230V
Input Current: 8.8A
Input Frequency:50/60HZ
Input PH : 1
Output Power : 750W
Output Voltage: 0-230V
Output Current: 5.5A
Output Frequency:0-300Hz
Output PH :3
Temperture: 0-55
Place of Origin:Japan
Efficiency:IE 1
OTHER SUPERIOR PRODUCTS
Similar Products
SGMAH-02BAA21 SGMAH-A6AAA4C SGMAH-A3AAA41 SGMAH-01AAA21
SGMAH-08AAA21 SGMAH-08AAF41 SGMAH-02AAA41 SGMAH-02AAA21
SGMAH-08AAA41 SGMAH-04AAA41 SGMG-05A2AB SGMG-30A2AB
SGMG-44A2AB SGMG-09A2AAB SGMG-06A2B SGMG-09VSAB
SGMG-09A2ACS SGMG-05AWABB SGMG-09A2AC SGMG-30A2RAF
SGMG-20A1U-HS21 SGMG-20A2A SGMG-05VSABS SGMG-30ASRAB
SGMG-13ASR SGMG-09V2AAS SGMG-09AWAB SGMG-09VSACS
SGMG-09VWW-NJ12 SGMG-09VSA13 SGMG-44AWA-NJ12
SGMGH-05ACC21 SGMGH-05VSABS SGMGH-44ACA61
SGMGH-05DCA61 SGMGH-20ACA61 SGMGH-09ACA61
SGMGH-44CA-TV11 SGMGH-30ACA21 SGMGH-30DCA61
USASEM-02FJ12 USASEM-02FJ12 USASEM-15FJ11
USASEM-03CFJ11 USASEM-05FJ12 USASEM-08FJ12
USASEM-01CF12 USAFED-30-FJ11 USAFED-09-FJ11
USAFKD-50-FJ11 USAREM-01CF J12 SGM-08A3F J43
SGM-08AAF J12 SGM-08A3F J53 SGM-08A2F J34
SGM-02A3F J73 SGMAH-01AAA-FJ21 SGMG-75V6V-FJ11
SGMS-70A6V-FJ11 SGM-01B3FJ12 R404-011EL27 RM-H6A6ZMR039
This section shows a standard example of connecting Σ-Series products to peripheral devicesand briefly explains how to connect to each peripheral device.
NOTE Read the following notes before wiring:
• Connect only one cable to one terminal. Never connect two cables to one terminal.
• Do not solder the cable.
• Peel back the cable shield by about 10mm (0.39in.) min. Then insert the cable into the terminal securely and tighten the screw. Never leave the bare wires outside of the termianl.
• When the cable is inserted into the flat terminal, use the following ferrules. Non−insulated ferrules, 2.5mm2 or less (Made by PHOENIX CONTACT)
<Reference> Terminal block type: FRONT 2.5H/SA5
a) Form a power ON sequence so that the main power is turned OFF when a servo alarm signal is output. (See the circuit diagram shown on the previous page.)
b) Hold down the power ON push-button for at least two seconds. The Servopack outputs
a servo alarm signal for approximately two seconds or less when the power is turned ON. This operation is required to initialize the Servopack.
Avoid frequently turning the power ON and OFF. Since the Servopack has a capacitor in the power supply, a high charging current flows (for 0.2 second) when the power is turned ON. Therefore, frequently turning the power ON and OFF causes the main power devices (such as capacitors and fuses) to deteriorate, resulting in unexpected problems.