Bộ điều khiển Electric Servo Drive Industrial Yaskawa 0-55℃ 100W Input 50/60HZ SGDM-01ADA-R
Electric Servo Drive Industrial Yaskawa 100W Input 50/60HZ 0-55℃ SGDM-01ADA-R
Quick Details
Model Number: SGDM-01ADA-R
Input Voltage:200-230V
Input AMPS : 2.0
Input Frequency:50/60HZ
Input PH : 1
Series : Sigma 2 (Σ-II Series)
Output Power : 100W
Output Voltage: 0-230V
Output AMPS: 0.87
Output Frequency:0-300Hz
Temperture: 0-55℃
Place of Origin:Japan
Efficiency:IE 1
Similar Products
SGDM-01AD
SGDM-01ADA
SGDM-01ADA/SGDH-01AE+SGMAH-01AAA21
SGDM-01ADA+SGMAH-01AAAG761
SGDM-01ADA-RY5
SGDM-01BDA
SGDM-02ADA
SGDM-02ADA/SGDH-02AE+SGMAH-02AAA21
SGDM-02ADA+SGMAH-02AAA2C
SGDM-02ADA+SGMPH-02AAA41
SGDM-02ADA+SGMPH-02A1A21
SGDM-02AD-R
SGDM-02BDA
SGDM-02BDA
SGDM-02BDA+SGMAH-02BBAB1
SGDM-04AC-AD2B
SGDM-04AC-SD1
SGDM-04AC-SD2A
SGDM-04ACSD2B
SGDM-04AC-SD2B
SGDM-04AC-SD2BM
SGDM-04AC-SD2M
SGDM-04AD
SGDM-04AD+SGMAH-04AAA41
SGDM-04ADA
SGDM-04ADA +SGMAH-04AAA21
SGDM-04ADA +SGMAH-04AAA41
SGDM-04ADA+SGMPH-04A1A21
SGDM-04ADA-RY1
SGDM-04ADAY360
SGDM-04AD-R
SGDM-04AD-RY1
SGDM-04ADY39
Installation and Maintenance: Installation and maintenance or replacement must be carried out by suitably qualified service personnel, paying particular attention to possible electrical and mechanical hazards. Weight: Large drives are heavy, the center of gravity may be offset and removable covers shield internal components. When handling, take appropriate precautions and lift the equipment using permanent, fixed surfaces, such as the base; avoid lifting the device using protective cover shields that may be loose. Beware of sharp edges; use protective gloves when handling such assemblies. Flying Leads and Loose Cables: Ensure that flying leads or loose cables are suitably restrained, to prevent snagging or entanglement, or are disconnected before carrying drives with such leads or cables. Generation: If a motor is driven mechanically, it may generate hazardous voltages which are conducted from its power input terminals to the drive.
The power connector must be suitably guarded to prevent a possible shock hazard. Loose Drives: When running an unmounted drive, ensure that the cooling fan is adequately guarded and sufficient airflow is provided around the drive to ensure adequate cooling. The mounting surface of the drive is a heat sink and its surface temperature may increase when the drive is operating. If a motor is connected to the drive, remove the key which otherwise could fly out and restrain the motor before applying power to the drive. Da
maged Cables: Damage to cables or connectors may cause an electrical hazard. Ensure there is no damage before energizing the system. Supply: Drives connect to a permanent main power source; not a portable power source. Suitable fusing and circuit protection devices are required. Consult the instructions and adhere to local and national regulations before connecting and energizing the drive. Safety Logic Signals:
Logic signals from the drive are interruptible signals; they are removed when power is removed from the drive. Consult the manual for information on auxiliary power connections that may be employed when these signals are used for safety purposes. Safety Requirements: The safe incorporation of Tol-O-Matic SSD products into a machine system is the responsibility of the machine designer, who should comply with the local safety requirements at the place where the machine is to be used. In Europe this is likely to be the Machinery Directive, the ElectroMagnetic Compatibility Directive and the Low Voltage Directive.
In the United States this is likely to be the National Electrical Code. Mechanical Connection: Drives must be installed inside an electrical cabinet that provides environmental controls and protection. Installation information for the drive is provided in the manual and list the minimum installation requirements for the drive are provided in the manual. Motors and controlling devices that connect to the drive should have specifications that complement the capabilities of the drive. Motors: Motors controlled by the drive should only connect to the drive; they should not connect directly to the AC line. U
The added or improved functions differ depending on the SERVOPACK model or software version number:
• SGDM-D
• SGDM-DA
• SGDM-A
(Software version No. 32 or later) Refer to the following table for the added or improved functions for each model. This table can also be used in reference to other SERVOPACK models.
Function Item Description Σ-II Series SERVOPACK SGDMReference D DA Section DA with Software Version No. 32 or later Applicable capacity range 30W to 3.0 KW Applicable Applicable Applicable – 30W to 15.0 kW N/A Applicable Applicable – Speed feed forward In the position control mode, the speed feed forward reference using an analog voltage can be input by the speed reference (VREF) input. N/A Applicable Applicable 9.4.3 Torque limit using an external torque limit and analog voltage reference To enable the torque limit function using analog voltage reference only when either /P-CL or / N-CL signal is ON. N/A Applicable Applicable 8.9.4 Input signal polarity reversal To reverse the “Enabled” logic polarity of sequence input signal N/A Applicable Applicable 7.3.2 Output signal polarity reversal To reverse the “Enabled” logic polarity of sequence output signal N/A Applicable Applicable 7.3.3 Multiturn limit setting To set the upper limit of multiturn data when using an absolute encoder. N/A Applicable Applicable 8.4.7 “Multiturn limit disagreement” alarm detection To detect the alarm A.CC when the multiturn limit value set in the encoder does not agree with that in the SERVOPACK. N/A Applicable Applicable 8.4.8 Average movement filter of position reference To filter the position reference pulse of constant frequency inside the SERVOPACK. Either acceleration/deceleration filter or average movement filter can be selected. N/A Applicable Applicable 8.6.4 Notch filter Filtering function to suppress vibration according to the machine’s vibration frequency. N/A Applicable Applicable 9.4.10 Second stage notch filter and changeable Q value A second stage notch filter is added. And the Q value (sharpness of notching) can be changed. N/A N/A Applicable 10.3.4
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- Mitsubishi Motor HC-,HA-
Westinghouse Modules 1C-,5X- Emerson VE-,KJ-
Honeywell TC-,TK- Fanuc motor A0-
Rosemount transmitter 3051- Yokogawa transmitter EJA-
