Mô đun GE FANUC SERIES 90-30 PLC Digital I/O Module IC697PWR710 FACTORY SEALED
đại lý IC697PWR710 | nhà phân phối IC697PWR710
GE FANUC SERIES 90-30 PLC Digital I/O Module IC697MEM771 FACTORY SEALED
Product Description:
GE Fanuc Discrete input module for 90 – 30 series PLC offers 16 input points with one common power input terminal. It requires an AC power source for convenient operation. Module has LED indicators at the top to offer ON/OFF status of each point. Module has circuit wiring information on the surface towards the inside and circuit identification information on the outside surface. Module has a voltage rating of 120 VAC at 50/60 Hz, 0 – 132 VAC at 50/60 Hz, input current rating of 12 milli-Amps and a power rating of 90 milli-Amps at 5 VDC. It has a maximum ON response time of 30 milli-seconds and maximum OFF response time of 45 milli-seconds. Module is compatible with input devices such as pushbuttons, limit switches and electronic proximity switches. Input/output module provides the interface between the PLC and external input devices such as proximity sensors, push buttons, switches and BCD thumbwheels. It supports different voltage ranges, types, current capacity, isolation and response time to meet your application.
Product Details:
Input modules provide the interface between the PLC and external input devices such as proximity sensors, push buttons, switches and BCD thumbwheels. Output modules provide the interface between the PLC and external output devices such as contactors, interposing relays, BCD displays and indicator lamps. This module requires an AC power source, it cannot be used with a DC power source.
Product Summary:
-
Type of Device: Power Supply Module Input 120/240VAC or 125 VDC 50/60HZ
-
Nominal Rated Voltage: 120/240 VAC or 125 VDC
-
Input Voltage Range AC: 90 to 264 VAC, 47 to 63 Hz
-
Input Voltage Range DC: 100 to 150 VDC
-
Input Power: 90 watts maximum at full load
-
Description: Power Supply
-
Type of Device: Power Supply Module Input 120/240VAC or 125 VDC 50/60HZ
-
Nominal Rated Voltage: 120/240 VAC or 125 VDC
-
Input Voltage Range AC: 90 to 264 VAC, 47 to 63 Hz
-
Input Voltage Range DC: 100 to 150 VDC
-
Input Power: 90 watts maximum at full load
-
Input Half Cycle Peak Inrush: 3 amps (typical)
-
Power Factor: > .95
-
Output Power: 56 watts maximum
-
Output Voltage: +5 VDC: 4.90 to 5.25 volts (5.1 volts nominal)
-
Overvoltage Limit: 6.2 volts (typical), electronic overvoltage protection
-
Overcurrent Limit: 12 amps (typical), electronic current limit
-
Ride Through Time: 21 milliseconds minimum (from loss of AC input)
-
VME: System designed to support the VME standard C.1
-
Features: Operation from 120/240 VAC or 125 VDC, Five volt DC output up to 11 amps, Slide-in rack mount construction, Electronic short circuit overcurrent protection provided on 5 volt bus, Two rack operation from a single power supply, Power factor corrected on AC inputs, Jumper for overvoltage protection devices.
-
Product Description: This Power Supply Module for the programmable controller is a rack-mounted unit that plugs directly into a 48-pin backplane-mounted connector in the leftmost slot in the rack. It provides +5 volt power and logic level sequencing signals to the backplane. This power supply may be used either in a single rack application, or may also be used to provide power to a second rack if the total load is within the supply rating. Interconnection to the second rack is through an available prewired cable (see the ordering instructions on the last page of this data sheet). The power supply output will ride through a one-cycle total loss of input power at full load. Protection is provided for overcurrent and overvoltage fault conditions.
Related Product Recommendation:
| GE | VCIB-16A | GE | DS200CDBAG1ACA |
| GE | VMIVME-7671-421000 | GE | DS200DCFBG2BNC |
| GE | 269PLUS-100P-120 | GE | DS200FCRRG1AKD |
| GE | 369-HI-0-0-0-0 | GE | DS200LDCCH1ARA |
| GE | 369-HI-R-0-0-0 | GE | DS200LRPAG1AGF |
| GE | 531X111PSHAPG3 | GE | DS200PCCAG5ACB |
| GE | 531X113PSFARG1 | GE | DS200PCCAG9ACB |
| GE | 531X123PCHACG1 | GE | IC693DSM302 |
| GE | 531X139APMARM7 | GE | IC693MDL330 |
| GE | 531X303MCPBCG1 | GE | IC693MDL646 |
| GE | 531X305NTBACG1 | GE | IC693MDL655 |
| GE | 531X305NTBAPG1 | GE | IC693MDL730 |
| GE | IC200ALG322 | GE | IC693MDL752 |
| GE | IC200ALG620 | GE | IC693PBS105 |
| GE | IC200ALG630 | GE | IC693PCM301 |
| GE | IC200CHS002 | GE | IC200MDL742 |
| GE | IC200MDL740 | GE | IC200CPUE05 |
| GE | IC3600LTGA | GE | IC200PWR101 |
| GE | IC3600TUAA1 | GE | IC200PWR001 |
| GE | IC660BBD025 | GE | IC693PWR330 |
| GE | IC670MDL640 | GE | IC694APU300 |
| GE | IC670PBI001 | GE | IC694BEM331 |
| GE | IC693ACC310 | GE | IC694MDL645 |
| GE | IC693ALG223 | GE | IC694MDL655 |
| GE | IC693ALG390 | GE | IC694MDL740 |
The use of the product:
【Emerson】DeltaV Module / Servo Motor
【ABB】Input Output Module
【AB】Module / Touch Screen
【Rosemount】Pressure and Temperature Transmitter
【Yokogawa】Pressure Transmitter
【Yaskawa】Servo Drive / Servo Motor
【Mitsubishi】Servo Drive / Servo Motor
【GE】IC69 Series PLC/ Fanuc Servo Motor and Drive
