Mô đun Ge Fanuc IC660BBD025 ， 5/12/24 VDC 32-Circuit Sink I/O Block ， Genius I-O
Ge Fanuc IC660BBD025 , 5/12/24 VDC 32-Circuit Sink I/O Block , Genius I-O
Product Description
The IC660BBD025 is a 5/12/24 VDC 32-Circuit Sink I/O Block. This block is an intelligent, configurable module that interfaces the controller to devices that send or receive binary signals.
IC660BBD025 works with both 2-wire and 3-wire proximity switches, as well as other input devices. It is important to note that if the user plans to provide current to field output devices rather than receive current, a Source Block IC660BBD024 is recommended.
Source and Sink block versions each operate with direct current (12 to 24 volts). IC660BBD025 is also +5 volt TTL (transistor-transistor logic) compatible.
The block’s 32 circuits can be configured as input, output, or output with feedback. In output configurations, block architecture protects driver circuits against short circuits caused by wiring errors. Configurable features of the IC660BBD025 include Output Pulse Test capability, Input Filter Time, CPU Redundancy type, Output Hold behavior, and its readiness for use as a Bus Switching Module control.
Block terminals 5 through 46 are for connecting field devices. The user should wire the block power disconnects so that block power and input power can be removed at the same time. Simultaneous power removal ensures that the block will not power up unexpectedly when multiple inputs are activated.
IC660BBD025 ships with block diagnostics that monitor output and check actual switch state against expected or commanded switch state. The block handles a steady-state load of 0.5 Amps when operating normally.
Block behavior and circuits are configured using a handheld monitor. The monitor can also be used with LEDs on the chassis of the block itself to check operating status at a glance.
When installing the block, it is crucial to use a protective case and choose a place with no airborne contaminants. Adequate cooling and air flow are essential. Ground screws must connect to a reliable grounding system. To properly disconnect block power, circuit power must be disconnected.
| Rated Voltage: | 5/12/24 VDC |
| # of Points: | 32 |
| Input Range: | 4.9-5.3 VDC or 10-30 VDC |
| Load Current: | 0.5 |
| Operating Voltage: | 4.9-5.3 VDC or 10-30 VDC |
| Points per Common: | One group of 32 |
Technical Information
Specifications
|
Block Type: CatalogNumbers: 32Circuit12/24VDCSource:I /OBlock TerminalAssembly ElectronicsAssembly 32Circuit5 / 12 / 24VDCTTLSink: I / OBlock TerminalAssembly ElectronicsAssembly |
DC 32-circuit discrete input and output IC660BBD024 IC660TBD024 IC660EBD024 IC660BBD025 IC660TBD025 IC660EBD025 |
|
Size (height x width x depth): Weight LEDs (I/O Block) LEDs (each circuit) Block to Block Isolation HeatDissipation |
8.83” (22.44cm) x 3.56” (9.05cm) x 4.42” (11.23cm) 4 lbs. (1.8 kg) Unit OK, I / OEnabled Individual logic side indicators 850V
11W minimum with 8 inputs 18W maximum with 32 outputs at .5 amp |
|
Operating voltage (single source)
Ripple(maximum) Required DC power Power supply dropout times |
10 to 30 VDC (12 / 24 V supply) 4.9 to 5.3 VDC (5 V supply) (sink model only) absolute instantaneous limit 10% (12 / 24 volts) , 1% (5 volts) 150 mA typical, 300 mA maximum 4 mS at 12 volts, 20 ms at 24 volts |
|
Input Characteristics: Input voltage relative to (DC–) InputON,5 VDCsupply 12 VDC supply 24 VDCsupply InputOFF5 VDCsupply 12 VDC supply 24 VDC supply Input impedance (typical) Input processing time (typical) Selectable input filter times |
SourceBlocksSinkBlocks notapplicable0–0.8VDC 8–12VDC0–4VDC 18–24VDC0–6VDC notapplicable2–5VDC 0–6VDC6–12VDC 0–12VDC12–24VDC 3.3 K ohms 1.4 mS (plus selectable filter delay) 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, or 100mS |
|
OutputCharacteristics: Maximum output current (steady state) Maximum inrush current Block output current (total) Output OFF leakage current (maximum) Output turn–on delay (maximum) Output voltage drop Output Diagnostics |
0.5 amps per circuit 4 amps up to 10 mS (once every .5 sec. maximum) 16 amps 10ïA 0.5 mS 2.0 volts maximum at 4 amps inrush Switch Fault |
|
Environmental: Operating temperature Storage temperature Humidity Vibration |
0 C to +60 C (+32 to +140 F) –40 to +100 C (–40 to +212 F) 5% to 95% (non–condensing) 5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
