Mô đun Ge Fanuc IC660BBA104 ， Genius Analog I/O Block Series 90-30 PLCs
Ge Fanuc IC660BBA104 , Genius Analog I/O Block Series 90-30 PLCs
Product Description
The IC660BBA104 is a Genius Analog I/O Block of GE Fanuc series 90-30 PLCs. It belongs to the Analog Mixed Modules group and can be powered with either 115 VAC or 125 VDC. It has four inputs and two outputs whose I/O range is between 4 mA to 20 mA and provides the system with different types of diagnostics. Circuits are isolated, and accuracy of input is as precise as 0.1%.
Power is provided to the block and all the circuits from a single input, so that external power is not needed to process signals. After the signal enters the block, circuits apply linear scaling to convert it to engineering units. With every scan, 8 bytes of data containing those engineering data are broadcasted. The output data broadcast in 4 bytes. The block provides an output that connects to a Bus Switching Module (IC660BSM21) and is compatible with Genius Bus Controllers, PCIM and QBIM modules. To configure the IC660BBA104 Genius Analog I/O Block, the user needs a Hand-held monitor version 3.7 or later. The programming software is Logicmaster 6 ver. 4.02 or later. CPUs that are compatible with the block are rev. 105 or later for Series Six PLCs and rev. 3.0 or later for series 5 PLCs.
The block can be configured to detect input alarms, hold the last output state, or a default state and receive output feedback. The time to convert a signal to a value can be up to 400ms, and the block can work if there is CPU redundancy. Diagnostic checks involve detection of input open wire, input high and low alarms for each input individually, I/O over range and under range signal detection, and errors in output feedback. The IC660BBA104 Genius Analog I/O Block has 32 terminals. The power source connects to terminals 5 and 6. I/O cables connect to the self-powered inputs 17 to 32. Outputs connect to terminals 11-12 and 14-15. If they are both grounded, a 10-ohm resistor is needed to prevent circuit damage. The bus switching module connects to terminals 9-10.
| Rated Voltage: | 115 VAC/ 125 VDC |
| # of Points: | 4 Inputs / 2 Outputs |
| Input Range: | 4 mA to 20 mA |
| Output Range: | 4 mA to 20 mA |
| Operating Voltage: | 93-132 VAC / 105-145 VDC |
| Points per Common: | One group of 4 Inputs and one group of 2 Outputs |
Technical Information
Specifications
|
Block Type: CatalogNumbers: 115VAC/125VDCCurrentSourceAnalogblock TerminalAssemblyOnly ElectronicsAssemblyOnly 24/48VDCCurrentSourceAnalogblock TerminalAssemblyOnly ElectronicsAssemblyOnly |
Four input / 2 outputcircuits IC660BBA104 IC660TBA104 IC660EBA104 IC660BBA024 IC660TBA024 IC660EBA024 |
|
Size (height x width x depth) Weight: LED’s (I/O Block): HeatDissipation: BSMControl: |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) 4 lbs. (1.8 kg) UnitOK,I / OEnabled 12 Wattsmaximum Switches one 24 / 48 VDC BSM (IC660BSM021) |
| Block to Block Isolation: Group to GroupIsolation: | 1500 V for one minute 300 V rms |
|
115VAC/125 VDCblockpower: Powersupplyvoltage Maximumcurrent Frequency / ripple Power supply dropout time |
115VAC125VDC VVDC 250mA140mA 47–63 Hz10%max.ripple 1cycle10 mSmin. |
|
24/48 VDCblockpower: Powersupplyvoltage Maximumcurrent Ripple Power supply dropout time |
18–56 VDC 600mA 10% max. 10 mS min. |
|
InputSignalCharacteristics: Input accuracy (at 25 C) Inputresolution Inputconversion time Range Overrangecapacity Inputdiagnostics Channel to channel isolation Thermal drift (from 25 C) |
0.1% of full scale reading 1ïA 16.6mS to 400mS (user selectable) 4mA to 20mA 0mA to 25mA Underrange,Overrange,HighAlarm,LowAlarm,OpenWire 300 voltsRMS 70 PPM per degree C typical |
| InputImpedance: | 100 ohms $ 5% |
| Normal Mode Rejection: | –45 dB at 50, 60 Hz |
|
Input ExcitationCharacteristics: Opencircuitvoltage Shortcircuitcurrent Loopimpedance |
24 VDC < 75mA 1000ohmsmax.(0mAto20mA)800ohmsmax.(20mAto25mA) |
|
OutputSignalCharacteristics: Output accuracy at 25 C Outputresolution Outputupdatefrequency Range Overrangecapacity Outputdiagnostics: Load: Thermaldrift (from 25C): |
0.15% of full scale reading 6ïA 6mS to 8mS typical 4mA to 20mA 0mA to 24mA Underrange, Overrange, Feedback error 0 ohms to 850 ohms 35 PPM per degreeC typical |
|
Environmental: Operating Temperature Storage Temperature Humidity Vibration |
0C to +60C (+32F to +140F) –40C to +100C (–40F to +212F) 5% to 95% (non–condensing) 5 – 10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G |
