Mitsubishi NEW 1-Axis AC Servo Drive MR-J4-350A 220V SERVO AMPLIFIER 3.5KW in stock

 

Specification of Servo Drive MR-J4-350A

 

mode name		MR-J4-350A
Output	Rated Voltage	3-phase 170 VAC
	Rated Current (A)	17.0
Main Circuit Power Supply	Voltage/Frequency	3-phase 200 VAC to 240 VAC, 50/60 Hz
	Rated Current (A)	16.0
	Permissible Voltage Fluctuation	3-phase 170 VAC to 264 VAC
	Permissible Frequency Fluctuation	±5% maximum
Control Circuit Power Supply	Voltage/Frequency	1-phase 200 VAC to 240 VAC, 50/60 Hz
	Rated Current (A)	0.2
	Permissible Voltage Fluctuation	1-phase 170 VAC to 264 VAC
	Permissible Frequency Fluctuation	±5% maximum
	Power Consumption (W)	30
Interface Power Supply		24 VDC ±10% (required current capacity: 0.5 A (including CN8 connector signal))
Load-Side Encoder Interface		high-speed serial communication
Tolerable Regenerative Power of the Built-in Regenerative Resistor(W)		100
Control Method		Sine-wave PWM control/current control method
Dynamic Brake		Built-in
Protective Functions		Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection,encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, over-speed protection, error excessive protection, magnetic pole detection protection, linear servo control fault protection
Position Control Mode	Maximum Input Pulse Frequency	4 Mpps (when using differential receiver), 200 kpps (when using open-collector)
	Positioning Feedback Pulse	Encoder resolution: 22 bits
	Command Pulse Multiplying Factor	Electronic gear A/B multiple, A: 1 to 16777216, B: 1 to 16777216, 1/10 < A/B < 4000
	Positioning Complete Width Setting	0 pulse to ±65535 pulses (command pulse unit)
	Error Excessive	±3 rotations
	Torque Limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Speed Control Mode	Speed Control Range	Analog speed command 1:2000, internal speed command 1:5000
	Analog Speed Command Input	0 V DC to ±10 V DC/rated speed (Speed at 10 V is changeable with
	Speed Fluctuation Rate	±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%) ±0.2%maximum(ambient temperature 25 ± 10 centigrade degree) only when using analog speed command
	Torque Limit	Set by parameters or external analog input (0V DC to +10 VDC/maximum torque)
Torque Control Mode	Analog Torque Command Input	0VDCto±8VDC/maximum torque (input impedance: 10 to 12 kohm)
	Speed Limit	Set by parameters or external analog input (0VDC to ± 10 VDC/rated speed)
Fully Closed Loop Control		Available in the future
Safety Function		STO (IEC/EN 61800-5-2)
Communication Function		USB: Connect a personal computer (MR Configurator2 compatible)
Structure (IP Rating)		Force cooling, open (IP20)
Close Mounting		Possible
Weight (kg)		2.3

 

Product Number	Description
MR-J4-100A	SERVO AMP 1KW 200V
MR-J4-100A4	1KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-100B	SERVO AMP 1KW 200V SSCNET
MR-J4-100B4	1KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-10A	100W SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (200V 1-PHASE OR 3-PHASE)
MR-J4-10B	SERVO AMP 100W 200V SSCNET
MR-J4-11KA4	11KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-11KB4	11KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-15KA4	15KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-15KB4	15KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-200A	SERVO AMP 2KW 200V
MR-J4-200A4	2KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-200B	SERVO AMP 2KW 200V SSCNET
MR-J4-200B4	2KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-20A	SERVO AMP 200W 200V
MR-J4-20B	SERVO AMP 200W 200V SSCNET
MR-J4-22KA4	22KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-22KB4	22KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-350A	SERVO AMP 3.5KW 200V
MR-J4-350A4	3.5KW SERVO AMPLIFIER (DIGITAL OR ANALOGUE CONTROL) (400V 3-PHASE)
MR-J4-350B	SERVO AMP 3.5KW 200V SSCNET
MR-J4-350B4	3.5KW SERVO AMPLIFIER (SSCNET III BUS CONTROL) (400V 3-PHASE)
MR-J4-40A	SERVO AMP 400W 200V
MR-J4-40B	SERVO AMP 400W 200V SSCNET
MR-J4-500A	SERVO AMP 5KW 200V

 

 

 

Packaging & Delivery

 

 

Packaging Details
Cartons

 

Delivery Time
Whithin 3-5 days

 

 

 

 

 

【Emerson / Delta V】Module

【ABB】Input Output Module

 

【AB】Module / Touch Screen

 

【Rosemount】Pressure and Temperature Transmitter

 

【Yokogawa】Pressure Transmitter

 

【Yaskawa】Servo Drive / Servo Motor

【GE/Fanuc】IC69 Series PLC

 

【Mitsubishi】Servo Drive / Servo Motor

 

 

 

 

 

 

Company Introduction