Bộ điều khiển High Efficiency Industrial Servo Drives Yaskawa Servopack SGDL-02AP 200W Input AMPS4.0
Efficiency Industrial Servo Drives Yaskawa servopack SGDL-02AP 200W Input AMPS4.0
Quick Details
Brand Name:Yaskawa
Model Number:SGDL-02AP
Input Voltage:200-230V
Input AMPSt: 4.0
Input Frequency:50/60HZ
Input PH : 1
Series : Sigma 2 (Σ-II Series)
Output Power : 200W
Output Voltage: 0-230V
Output AMPS: 2.0
Output Frequency:0-300Hz
Output PH :3
Temperture: 0-55℃
Place of Origin:Japan
Efficiency:IE 1
OTHER SUPERIOR PRODUCTS
| SGDL-02AP |
| SGDL-02AP+SGML-02AF14 |
| SGDL-02AS |
| SGDL-03BP |
| SGDL-04AP |
| SGDL-04AP+SGML-04AF14 |
| SGDL-04AP+SGML-04AF14 |
| SGDL-04AS |
| SGDL-04SVS |
| SGDL-08AF12 |
| SGDL-08AP |
| SGDL-08AP+SGML-08AF14 |
| SGDL-A5BP |
| SGDM-01AD |
| SGDM-01ADA |
| SGDM-01ADA/SGDH-01AE+SGMAH-01AAA21 |
| SGDM-01ADA+SGMAH-01AAAG761 |
| SGDM-01ADA-RY5 |
| SGDM-01BDA |
| SGDM-02ADA |
| SGDM-02ADA/SGDH-02AE+SGMAH-02AAA21 |
| SGDM-02ADA+SGMAH-02AAA2C |
| SGDM-02ADA+SGMPH-02AAA41 |
| SGDM-02ADA+SGMPH-02A1A21 |
| SGDM-02AD-R |
| SGDM-02BDA |
Do not use 1 or 2.
Be sure to disconnect the lead between B2 and B3, before connecting an external regenerative registor to the SERVOPACK.
For connecting a DC reactor, refer to 6.4.8 DC Reactor for Harmonic Suppression.
Power supply
Three-phase 200 VAC
Protects the power supply line by shutting the circuit OFF when overcurrent is detected.(Refer to 5.8.9.)
Used to eliminate external noise from the power line.(Refer to 5.8.10.)
Connect an external regenerative resistor to terminals B1 and B2 if the regenerative capacity is insufficient.
(Refer to 5.8.6.)
• Conduct trial operation on the servomotor alone with the motor shaft disconnected from machine to avoid
any unexpected accidents.
Failure to observe this caution may result in injury.
• Before starting operation with a machine connected, change the settings to match the parameters of the
machine.
Starting operation without matching the proper settings may cause the machine to run out of control or malfunction.
• Forward run prohibited (P-OT) and reverse run prohibited (N-OT) signals are not effective during zero point
search mode using parameter Fn003.
• When using the servomotor for a vertical axis, install the safety devices to prevent workpieces to fall off due
to occurrence of alarm or overtravel. Set the servomotor so that it will stop in the zero clamp state at
occurrence of overtravel.
Failure to observe this caution may cause workpieces to fall off due to overtravel.
• When not using the normal autotuning, set to the correct moment of inertia ratio.
Setting to an incorrect moment of inertia ratio may cause vibration.
• Do not touch the SERVOPACK heatsinks, regenerative resistor, or servomotor while power is ON or soon
after the power is turned OFF.
Failure to observe this caution may result in burns due to high temperatures.
• Do not make any extreme adjustments or setting changes of parameters.
Failure to observe this caution may result in injury due to unstable operation.
• When an alarm occurs, remove the cause, reset the alarm after confirming safety, and then resume operation.
Failure to observe this caution may result in injury.
• Do not use the servo brake of the servomotor for ordinary braking.
Failure to observe this caution may result in malfunction.
